The short answer, and the part the datasheet leaves out
An elastomeric sealant is a material that cures into a rubber-like solid—flexible, compressible, and able to recover its original shape after deformation. The formal definition is fairly simple. The part that matters in practice is messier: two suppliers can sell you the "same" elastomeric sealant and one of them will shut down your production line.
I review material specs and finished goods for an industrial components company—roughly 200+ items annually, across sealants, coatings, and polymer-based parts. Over four years of that, I've rejected about 18% of first deliveries. Not because the products were "bad" in some abstract sense. Because they didn't match the spec we agreed on, line by line, batch by batch.
Here's my position up front, since this is a conclusion-first kind of piece: in time-critical industrial work, the certainty of delivery and batch consistency is worth paying for. The lowest quoted price is frequently not the lowest total cost. I've watched this play out with Dow Corning sealants, with generic RTV coatings, and with a pharma-adjacent supplier that looked perfect on paper and missed the adhesion spec by a mile.
What elastomeric sealants actually are (and why "equivalent" is a dangerous word)
Elastomeric sealants cover a wide range: silicone, polyurethane, polysulfide, acrylic, and various hybrids. All of them form elastic seals. Their performance envelopes, however, are not interchangeable. A silicone elastomer might handle 200°C continuous service and stay flexible at -50°C. A polyurethane might beat it on abrasion resistance but stiffen at temperature extremes.
Dow Corning (now part of Dow) built its reputation on silicone chemistry. Their sealant lines—RTV coatings, adhesives, encapsulants—reflect that focus. The Dow Corning 3140 RTV coating is a useful example: a one-part, room-temperature-vulcanizing silicone that cures into a tough elastomer with good dielectric properties. It's common in electronics conformal coating, automotive gasketing, and industrial applications where you need adhesion plus flexibility plus electrical insulation.
From the outside, a 3140-style RTV coating looks like "just silicone." People assume any RTV silicone will do. What they don't see is the curing profile, the adhesion promoter chemistry, the outgassing behavior, and the lot-to-lot consistency. I've seen a "cheaper equivalent" stay tacky for six days when the spec called for tack-free in four hours. That's not an equivalent. That's a different product wearing a similar marketing description.
If you're asking "what is an elastomeric sealant" in a sourcing context, the answer has to include the specification, not just the chemistry class. ASTM C920 is the standard specification for elastomeric joint sealants, and it's a decent starting point for understanding what "elastomeric" actually requires in performance terms. MIL-A-46146 shows up in aerospace and defense contexts for RTV silicones. The point is that the definition is always incomplete without the spec.
Where pharma simulation changes the question
Pharma simulation—process modeling and material compatibility testing in pharmaceutical development—puts polymers under a different kind of scrutiny. You're not just asking whether a seal holds pressure. You're asking whether it leaches anything into the product stream, whether it survives repeated sterilization cycles, and whether the documentation proves it.
Industrial applications of polymers in pharma tend to involve silicone tubing, gaskets, and seals that need to meet USP Class VI or ISO 10993 standards. I'm not a regulatory specialist (note to self: get better at reading FDA guidance documents without falling asleep), but I do know that material selection here is not a place to freewheel. If a supplier can't produce consistent documentation for every batch, you're building on sand. The material might pass the test. The paperwork might not pass the auditor.
The $600 mistake I keep bringing up in meetings
In 2022, we switched a sealant order to a lower-cost vendor to save about $600 on a batch. The material met the hardness spec on paper—Shore A 40, I think, though this was back before we tightened the acceptance criteria. What it didn't meet was the adhesion requirement on anodized aluminum. We found out three weeks later when 1,200 assemblies failed a pull test.
Rework cost: roughly $14,000. Production delay: five days. The vendor's response was that their product was "within industry standard." We rejected the batch. They redid it at their cost, but the delay was ours to explain to the customer.
That was the last time procurement and I had a "you handle the price, I handle the spec" conversation. Now every contract includes a first-article inspection clause and a defined batch acceptance protocol. It slows down the purchasing process by maybe two days. It has saved us at least three rework events since.
Why I pay for delivery certainty
In March 2023, we needed a specific Dow Corning sealant for a customer's maintenance window. The distributor with the lowest price quoted 7-10 business days. The premium distributor guaranteed three-day delivery. We paid about $380 more on the order.
The cheap option would have missed the window. Missing that window would have cost the customer roughly $12,000 in downtime. The math isn't complicated. What's complicated is getting people to accept it before the emergency happens.
Honestly, I'm not sure why delivery certainty varies so wildly among distributors carrying the same product line. My best guess is it comes down to stocking depth and warehouse location, maybe some internal buffer practices I don't see. But the pattern is consistent enough that I now treat "guaranteed delivery" as a line item worth budgeting for, not a nice-to-have.
When the premium doesn't make sense
I should be honest about the limits. If you're prototyping in a lab, or running low-volume operations where a missed deadline is annoying but not catastrophic, the calculus changes. Top-tier silicone sealants are excellent products, but they're not universally necessary. For general-purpose gasketing or non-critical potting, a mid-tier product with a clear datasheet might serve you fine.
There's also a brand-name trap: paying for the logo doesn't fix a poorly written specification. The Dow Corning 3140 RTV coating is a strong product, but if your application involves continuous immersion in a harsh solvent, brand reputation doesn't replace a proper compatibility test. Most of the failures I've seen weren't material failures. They were specification failures dressed up as material failures.
What I've settled on, after four years of batch rejections and rework memos: pay for certainty in two places—the material's documented performance and the supplier's documented delivery. Everything else is negotiable. The cheapest option is only cheaper until it isn't.